Weather resistant resin for polyurethane enamels with fast drying speed and high gloss level. High resistance to the thermal shocks. Two-pack polyurethane topcoats for metal, with very good out-door durability, high gloss and colour retention. High compatibility with tintometer paste systems. Plasticising resin for two pack systems. Excellente wetting of pigments and substates. Top quality polyester for high solid varnish and enamels. Enabling to replace in formulation the hydroxylated acrylic resins with an excellent cost/performance balance. Top quality polyester for high solid varnish and enamels. Enabling to replace in formulation the hydroxylated acrylic resins with an excellent cost/performance balance. Resin for pure polyurethane or blended acrylic/polyurethane enamels for wood and metal primer and topcoats. Represents a perfect balance between technical performance, costs and easy use. It can be used also for marine applications. Isophtalic polyester resin specific for coil-coatings and stoving enamels. High oustanding chemical resistance and hardness. Good flexibility and high coverage. High reactivity isobutilated melamine resin. Fast curing for low temperature stoving enamels (80 - 100°C), high gloss and good flexibility. Medium-high reactivity butilated melamine resin for can coatings, OEM stoving enamels with high solid. Is reccomanded to boost the cure speed in polyurethane coatings. Organo metallic accelerator which does not significantly alter the pot-life of polyurethanes systems. Pigmented pastes styrene free, general purpose. Pigmented pastes styrene free,high pigment wettability. Ideal sole binder for wide range of fillers and putties. Very easy to sand, good adhesion properties and high stability. Medium flexbility. Binder for adhesive, highly filled knifing fillers and putties for car, marble and stone. Fast curing, Very hard and easy to send. Rigid. Highly filled knifing fillers and putties for car repair. Good adhesion properties to various kinds of substrates. Medium flexibility. Ideal sole binder for wide range of fillers and putties. Very easy to sand, good adhesion properties and high stability. Medium flexbility. To improve the flexibility in UP systems. Medium reactivity, overbaking resistances to high temperature. High flexibility. To improve the flexibility in UP systems. In combination with same other Synteven grade to improve the flexibility. High flexibility. To improve the flexibility in UP systems. Medium reactivity, overbaking resistances to high temperature. High flexibility. Special grade. Ideal sole binder for wide range of fillers and putties for light putty on galvanized steel. Unpromoted resin to improve the flexibility in UP systems. Fast cold-curing resin, even at low temperatures, has been developped in order to have a very fast sandability after the application. Medium flexibility. Very high reactivity. Fast cold-curing resin, even at low temperatures. Excellent flexibility and adhesion with high reactivity and high stability properties. Very fast sanding time. To formulate clear and pigmented, coatings for wood and furniture and spray filler for automotive refinishing. High gloss, good reactivity and hardness. Rigid. To formulate spray filler for automotive refinishing. High gloss, low viscosity, good reactivity and hardness. Rigid. Similar to KL, but more flexible, longer pot-life and more compatible with nitrocellulose. Mixed aliphatic/aromatic polymer for non yellowing fast drying polyurethane coatings. Aliphatic polyisocyanate for non yellowing polyurethane coatings, high gloss retention. Aliphatic polyisocyanate for non yellowing polyurethane coatings, high gloss retention. Solvent free. Aliphatic polyisocyanate for non yellowing polyurethane coatings, high gloss retention and high solid. Aromatic adduct for glossy polyurethane coatings or to use as plasticising partner of more brittle isocyanates.
FTALON 1680 / 70 ABT
Solids content %
70 ± 1Solvent(s)
Butyl AcetateBrookfield Viscosity at 25°C - mPas
2000 - 4500Acid value on solids - mg KOH/g
10 - 20% OH on solids
3,4 ± 0,2Max colour - Gardner scale
3FTALON 269 / 60 X
Solids content %
60 ± 2Solvent(s)
XyleneBrookfield Viscosity at 25°C - mPas
2000 - 4000Acid value on solids - mg KOH/g
9 - 15% OH on solids
3,7 ± 0,2Max colour - Gardner scale
3FTALON 60 / 60 X
Solids content %
60 ± 1Solvent(s)
XyleneBrookfield Viscosity at 25°C - mPas
1700 - 2300Acid value on solids - mg KOH/g
11 - 16% OH on solids
4,5 ± 0,2Max colour - Gardner scale
4Note
High flexibilityFTALON TAC / 60 X
Solids content %
60 ± 1Solvent(s)
XyleneBrookfield Viscosity at 25°C - mPas
2500 - 3100Acid value on solids - mg KOH/g
6 - 10% OH on solids
4,5 ± 0,2Max colour - Gardner scale
Note
Compatible with acrylicsFTALON TAC / 75 ABT
Solids content %
75 ± 1Solvent(s)
Butyl AcetateBrookfield Viscosity at 25°C - mPas
5800 - 7200Acid value on solids - mg KOH/g
6 - 10% OH on solids
4,5 ± 0,2Max colour - Gardner scale
Note
Compatible with acrylicsFTALON TN / 65 X
Solids content %
65 ± 1Solvent(s)
XyleneBrookfield Viscosity at 25°C - mPas
4500 - 5500Acid value on solids - mg KOH/g
20 - 27% OH on solids
4,7 ± 0,2Max colour - Gardner scale
3Note
Metal adhesionITALESTER 300
Solids content %
59 ± 2Solvent(s)
SN 150 / ButilglycolBrookfield Viscosity at 25°C - mPas
2500 - 3500Acid value on solids - mg KOH/g
5 - 12% OH on solids
2,7 ± 0,2Max colour - Gardner scale
2ITAMIN M 170 P
Solids content %
58 ± 2Solvent(s)
IsobutanolBrookfield Viscosity at 25°C - mPas
300 - 700Acid value on solids - mg KOH/g
2Max free formaldehyde %
≤ 0,9Max colour - Gardner scale
≤ 1ITAMIN M 184
Type
MFSolids content %
78 ± 2Solvent(s)
ButanolBrookfield Viscosity at 25°C - mPas
5000 - 8000Acid value on solids - mg KOH/g
2Max free formaldehyde %
≤ 0,5Max colour - Gardner scale
MITTEL 6772
Type
Additive% of use
0,05 - 2,0Effect
Curing enhancerDesigned for
Polyurethane 2K SystemsApplication methods
SprayMITTEL 6821
Type
Additive% of use
0,2 - 2Effect
Curing enhancerDesigned for
Polyurethane systemsApplication methods
SpraySYNTEVEN 105
Solids content %
100Solvent(s)
Solvent freeBrookfield Viscosity at 25°C - mPas
600 - 700Acid value on solids - mg KOH/g
18 - 22Note
For tinting paste, Styrene freeSYNTEVEN 107
Solids content %
100Solvent(s)
Solvent freeBrookfield Viscosity at 25°C - mPas
250 - 350Acid value on solids - mg KOH/g
15 - 25Colour
≤ 150 AphaNote
For tinting paste, Styrene freeSYNTEVEN 404
Solids content %
62,5 ± 1,5Solvent(s)
StyreneAcid value on solids - mg KOH/g
5 - 15Iodine colour value
≤ 15 IodineSYNTEVEN 430
Solids content %
64 ± 1,5Solvent(s)
StyreneAcid value on solids - mg KOH/g
20 - 30Iodine colour value
≤ 15 IodineDesigned for
MarbleApplication methods
Knifing PuttySYNTEVEN 432
Solids content %
61 ± 1Solvent(s)
StyreneAcid value on solids - mg KOH/g
15 - 25Iodine colour value
≤ 10 IodineApplication methods
Knifing PuttySYNTEVEN 440
Solids content %
62,5 ± 1,5Solvent(s)
StyreneAcid value on solids - mg KOH/g
5 - 15Iodine colour value
≤ 15 IodineApplication methods
Knifing PuttySYNTEVEN 443
Solids content %
65 ± 1Solvent(s)
StyreneAcid value on solids - mg KOH/g
≤ 15Iodine colour value
≤ 15 IodineApplication methods
Knifing PuttySYNTEVEN 445
Solids content %
67 ± 1,5Solvent(s)
StyreneAcid value on solids - mg KOH/g
5 - 15Iodine colour value
≤ 10 IodineApplication methods
Knifing PuttySYNTEVEN 447
Solids content %
65 ± 1,5Solvent(s)
StyreneAcid value on solids - mg KOH/g
5 - 15Iodine colour value
≤ 10 IodineApplication methods
Knifing PuttySYNTEVEN 454
Solids content %
64,5 ± 1,5Solvent(s)
StyreneAcid value on solids - mg KOH/g
≤ 20Application methods
Knifing PuttySYNTEVEN 462
Solids content %
65,5 ± 1,5Solvent(s)
StyreneAcid value on solids - mg KOH/g
8 - 15Iodine colour value
≤ 3 IodineApplication methods
Knifing PuttySYNTEVEN 474
Solids content %
62,5 ± 1,5Solvent(s)
StyreneAcid value on solids - mg KOH/g
5 - 15Iodine colour value
≤ 15 IodineApplication methods
Knifing PuttySYNTEVEN 674
Solids content %
63 ± 15Solvent(s)
StyreneAcid value on solids - mg KOH/g
15 - 25Iodine colour value
≤ 30 Iodine Application methods
Knifing PuttySYNTEVEN 701
Solids content %
75 ± 1Solvent(s)
StyreneAcid value on solids - mg KOH/g
12 - 18Iodine colour value
≤ 100 AphaApplication methods
Spraing PuttySYNTEVEN 702
Solids content %
69 ± 1Solvent(s)
StyreneAcid value on solids - mg KOH/g
12 - 20Iodine colour value
≤100 AphaApplication methods
Spraing PuttyURONAL KFL
Chemical Nature
Aliphatic AromaticSolids content %
60Solvent(s)
Butyl Acetate% NCO
10,0 - 10,6Brookfield Viscosity at 25°C - mPas
280 - 360Max colour - Gardner scale
URONAL KL / ABT
Chemical Nature
Aliphatic AromaticSolids content %
60Solvent(s)
Butyl Acetate% NCO
10,2 - 10,8Brookfield Viscosity at 25°C - mPas
400 - 500Max colour - Gardner scale
URONAL NL
Chemical Nature
AliphaticSolids content %
75Solvent(s)
Xylene / PMA% NCO
16,0 - 17,0Brookfield Viscosity at 25°C - mPas
50 - 300Max colour - Gardner scale
Note
BiuretURONAL NL 100
Chemical Nature
AliphaticSolids content %
100% NCO
21,5 - 22,5Brookfield Viscosity at 25°C - mPas
2000 - 2800Max colour - Gardner scale
Note
TrimerURONAL NL 90
Chemical Nature
AliphaticSolids content %
90Solvent(s)
Butyl Acetate% NCO
19,1 - 20,5Brookfield Viscosity at 25°C - mPas
400 - 600Max colour - Gardner scale
Note
TrimerURONAL P 75 New Standard
Chemical Nature
AromaticSolids content %
75Solvent(s)
Ethyl Acetate% NCO
12,5 - 13,5Brookfield Viscosity at 25°C - mPas
1000 - 1500Max colour - Gardner scale
Note
Adduct
350 - 450
700 - 950
450 - 550
350 - 450
600 - 800
650 - 800
650 - 850
350 - 450
800 - 1100
350 - 450
400 - 500
1700 - 2100
750 - 950